Asus p9x79 red cpu led5/27/2023 If you are of the same mindset go Asus and you won't regret it. The bottom line is that I think most people would rather have an operational system than a customer support line to call when their brand new $300+ product doesn't work and needs to be RMAd for a refurbished one just like most would rather have a working car than a constantly breaking or lemon law car with a good warranty that gets fixed and/or replaced. Might not seem that hard but after this experience with EVGA it is much appreciated by me.ĪSUS gets dinged a lot for poor customer support on the web and this has always made me hesitant to order them in favor of EVGA who is known for their good customer service. They packed a ton of options into this product and made it all operational. In addition to this board having several benefits compared to EVGA (most importantly internal USB 3.0 headers), it worked right away without needing to use the new processor. As I had two business days after this to resolve the issue, I leveraged Amazon's lovely Prime $3.99 overnight service to have this Asus board and an extra CPU (just in case) to show up just in time. In a frustrating turn of events, I arrived last week and installed all of the new equipment to be greeted with an FF code from the EVGA board and it continuously rebooting. Unfortunately I did not have time as a luxury for this build as I was doing it as a present for my brother who lives on the other side of the country from me and this is why I went through the efforts to try and ensure a working MoBo. This led to little or no response from them and basically me being told that I could RMA the board with a several day turnaround time if I ran into issues. Before doing so, and while waiting for the product to arrive, I contacted their sales and support department, along with Matthew Hurwitz, their public "Assistant Product Manager" and requested the board be verified as operational. However, after posting on their forums and being reassured by some users that these issues had been resolved, I went ahead and ordered an EVGA X79 SLI board directly from EVGA. On this latest build, I hesitated initially to purchase EVGA x79 based on many of the reviews I viewed online with people stating problems with bad products showing up DOA or bad BIOS chips. The time now is 05:19.I have been a fan of EVGA for years and have only purchased their motherboards. Note that you should give at least one core for OS needs.Īll times are GMT -4. I think this info may help you to decide. Values greater than 20% will impair performance and are not recommended. The percentage of overlap nodes to the total number of mesh nodes should ideally be less than 10% for efficient partitioning. During partitioning, ANSYS CFX prints partitioning diagnostic information to the CFX-Solver Manager text window and output file about partition overlaps. These regions are responsible for communication and memory overhead during a parallel run. The partitioning of a mesh leads to the creation of overlap regions at the partition interfaces. Try to Use a Sensible Number of Partitions For partitions smaller than this, you are unlikely to see any significant performance increase and may even see parallel slow down.įor hexahedral meshes, good parallel performance improvements are usually not seen until a minimum of 75,000 nodes per partition is reached. Quote 2: This one is with "Intel i7 4930K Unlocked (6 x 3.4 GHZ) OVERCLOCKED UPTO 4.4 GHZ" and as a result of this overclocking, the first three components (highlighted in red) need to be changed due to compatibility issues.Ĭomputer Case: Aerocool X-Predator X1 Devil RedĬPU: Intel i7 4930K Unlocked (6 x 3.4 GHZ) OVERCLOCKED UPTO 4.4 GHZĬPU Cooling: Coolermaster Hyper 212 Evo - Low Noiseġ) Is the configuration (6 cores, 32 GB RAM etc) alright to comfortably run CFX/FLUENT? It would be mostly used for porous regions, vortex shedding analysis and a multiphase simulations, covering both steady and transient simulations.Ģ) Is the £100 increase in configuration due to overclocking reasonable?įor tetrahedral meshes, you may want to use a minimum of 30,000 nodes per partition. Monitors: 1 x 24" HD LED Widescreen Monitor - Black - 2ms - 1920x1080 - DVI/VGA Operating Systems: Microsoft Windows 7 Professional 64 BIT (Genuine DVD & COA Included) Hard Drive #1: 1 TB Seagate (1000 GB) SATA-III HDD 7200 RPM 64MB Power Supply: Corsair 450W PSU - Low Noise Graphics Card: 1 x NVIDIA GeForce GTX 750 - 2GB - (EVGA) - Superclocked - (PCI-E) Memory: Corsair Vengeance LP 32GB 1866 MHz (4x8GB) - Lifetime Warranty (DDR3) Quote 1: This one is with processor “Intel i7 4930K Unlocked (6 x 3.4 GHZ)”ĬPU: Intel i7 4930K Unlocked (6 x 3.4 GHZ)ĬPU Cooling: Intel Heatsink & Fan - Low NoiseĬPU Compound: Standard CPU Compound Supplied With Heatsink I need a bit of help in deciding the configuration and correct pricing for the PC:
0 Comments
Leave a Reply. |